Failed Fax Receiving

• Messages sorted by:[ date ][ thread ][ subject ][ author ]

Hello,

on my Linux Server is a ELSA MicroLink 14.4TL Firmware 2.22 connected.
I configured mgetty and tried to receive some faxes.
But i get only some errors. Who can help me. Where must i serach?

---  cut here  ---
An incoming fax transmission failed (+FHNG: -1):
Sender ID: _+49 7231 970711     _
Pages received: 1

Modem device: ttyS1

Communication parameters: +FCS:0,3,0,2,0,0,0,0
    Resolution : normal
    Bit Rate   : 9600
    Page Width : 1728 pixels
    Page Length: unlimited
    Compression: 0 (1d mod Huffman)
    Error Corr.: none
    Scan Time  : 0

Reception Time : 01:30


The fax receive was *not* fully successful
The Modem returned +FHNG: -1
     (Invalid +FPTS:xxx code)

Spooled G3 fax files:


  /var/spool/fax/incoming/fn62d792dS1-_+49-7231-970711-_.01
---  cut here  ---

In /var/log/log_mg.ttyS1 steht folgendes:

---  cut here  ---
yS1  mgetty: experimental test release 1.1.16-Jul05
yS1  check for lockfiles
yS1  locking the line
yS1  lowering DTR to reset Modem
yS1  send: \dATQ0V1H0[0d]
yS1  waiting for ``OK'' ** found **
yS1  send: ATS0=0Q0&D3&C1[0d]
yS1  waiting for ``OK'' ** found **
yS1  mdm_send: 'ATI'
yS1  unknown numerical modem id 140
yS1  mdm_send: 'AT+FCLASS=2.0' -> OK
yS1  mdm_send: 'AT+FAA=1;+FCR=1' -> OK
yS1  mdm_send: 'AT+FBO=1' -> OK
yS1  mdm_send: 'AT+FNR=1,1,1,0' -> OK
yS1  mdm_send: 'AT+FLI="49 7240 5564"' -> OK
yS1  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK
yS1  waiting...
yS1  wfr: waiting for ``RING''
yS1  send: ATA[0d]
yS1  waiting for ``CONNECT''
yS1  found action string: ``+FCO_''
yS1  start fax receiver...
yS1  fax_wait_for(OK)
yS1  fax_id: '+FTI:"+49 7231 970711     "'
yS1  transmission par.: '+FCS:0,3,0,2,0,0,0,0'** found **
yS1  mdm_send: 'AT+FLO=2' -> OK
yS1  fax_send: 'AT+FDR'
yS1  fax_wait_for(CONNECT)** found **
yS1  fax_get_page_data: receiving
/var/spool/fax/incoming/fn62d792dS1-_+49-7231- 970711-_.01... yS1 
timeout... yS1  mdm_read_byte: read returned -1: Interrupted system call
yS1  fax_get_page_data: cannot read from port (1)!: Interrupted system
call yS1  fax_get_page_data: page end, bytes received: 22426 yS1 
fax_get_page_data: aborting receive, timeout! ##### fax dev=ttyS1,
pid=6435, caller='none', name='', id='_+49 7231 970711     _',
+FHNG=-01,
pages=1, time=00:01:30
---  cut here  ---

Kind regards
Micha Holzmann